Haicom Electronics CORP. Is a professional consumer GPS. HI-204III USB; HI-204III; HI-206 PS2; HI-206 USB; GPS Antenna. Windows all USB driver ( Support. View and Download Haicom HI-204III user manual online. GPS Haicom REAL-TIME TRACKER HI-602. INTRODUCTION OF GPS USB DRIVER FILES.29 B.

• Usb Gps Driver

Mini size Waterproof Magneted HI-206 is a GPS receiver with RS-232 interfaces and USB connector and built-in active antenna for high sensitivity to tracking signal. HI-206 is very small in size and well suited to system integration and users who use any kinds of mobile devices, such as, Smartphone, PDA, notebook PC, iPad, etc. It satisfies a wide variety of applications for car navigation, personal navigation or touring devices, tracking and marine navigation purpose. Users can simply plug it into a mobile device or other type of handheld PC running with suitable mapping and routing software for navigation. OVERVIEW: Fast Acquisition Enhanced Sensitivity 20 Channels “All-In-View” Tracking GPS Sensor Module. The receiver continuously tracks all satellites in view and provides accurate satellite positioning data. The HI-206III is optimized for applications requiring good performance, low cost, and maximum flexibility; suitable for a wide range of OEM configurations including handhelds, sensors, asset tracking, Smartphone, laptop-centric personal navigation system, and vehicle navigation products.

Its 20 parallel channels and 4000 search bins provide fast satellite signal acquisition and short startup time. Tracking sensitivity of -159dBm offers good navigation performance even in urban canyons having limited sky view. Satellite-based augmentation systems, such as WAAS and EGNOS, are supported to yield improved accuracy. Both the LVTTL-level and RS232-level serial interface are provided on the interface connector.

Supply voltage of 3.3V, or 3.6V7V ( Typ. 5V ) are supported.

FEATURES:. 20 parallel channel GPS receiver.

4000 simultaneous time-frequency search bins. SBAS (WAAS, EGNOS) support.159dBm tracking sensitivity.

. HI-204 -USB Ultra High Sensitive USB GPS Receiver. General description of what. 1 GPS is and how it works HI-204III-USB Series Introductions.4 TROUBLESHOOTING.27 A. INTRODUCTION OF GPS USB DRIVER FILES.29 B.

WINDOWS 98 INTERFACE.32 1. Install GPS USB Driver. HI-204 -USB WATERPROOF Ultra High Sensitive USB GPS Receiver.

General description of what GPS is and how it works. GPS (Global Positioning System) is the only system today able to show you your exact position on the Earth anytime, in any weather, anywhere. GPS satellites, 24 in all, orbit at 11,000 nautical miles. Although GPS was designed for military use, many thousands of civilians make use of it. The satellites actually broadcast two signals, one is only for military use, and the other can be used by both military and civilians. Since GPS is passive (you only need to receive the signal), there are no restrictions on who can use the signal available to civilians. HI-204 -USB Series Introductions HI-204 -USB is a GPS receiver with USB interfaces and built-in active antenna for high sensitivity to tracking signal.

HI-204 -USB is well suited to system integration and users who use any kinds LaptopPC. It satisfies a wide variety of applications for car navigation, personal navigation or touring devices, tracking and marine navigation purpose.

USB port For notebook PC use: HI-204 -USB connect with a LaptopPC USB port. SECTION 1 INTRODUCTION 1.1 OVERVIEW Fast Acquisition Enhanced Sensitivity 20 Channels “All-In-View” Tracking GPS Sensor Module The receiver continuously tracks all satellites in view and provides accurate satellite positioning data.

The HI-204 -USB is optimized for applications requiring good performance, low cost, and maximum flexibility; suitable for a wide range of OEM configurations including handhelds, sensors, asset tracking, PDA-centric personal navigation system, and vehicle navigation products. 1.2 Features. 20 parallel channel GPS receiver.

4000 simultaneous time-frequency search bins. SBAS (WAAS, EGNOS) support.159dBm tracking sensitivity.,. Example: $GPGLL,2447.2073,N,E,104548.04,A, A.65.

Field Example Description 2447.2073 Latitude in ddmm.mmmm format Leading zeros transmitted Latitude hemisphere indicator, 'N' = North, 'S' = South Longitude in dddmm.mmmm format Leading zeros transmitted Longitude hemisphere indicator, 'E' = East, 'W' = West 104548.04 UTC time in hhmmss.ss format, 000000.00 235959.99 Status, 'A' = valid position, 'V' = navigation receiver warning. 4.1.4 GSA - GPS DOP AND ACTIVE SATELLITES GPS receiver operating mode, satellites used for navigation, and DOP values. Format: $GPGSA,.

Example: $GPGSA,A,3,26,21,09,17,10.8,02.1,10.6.07 Field Example Description Mode, 'M' = Manual, 'A' = Automatic Fix type, 1 = not available, 2 = 2D fix, 3 = 3D fix 26,21,09, PRN number, 01 to 32, of satellite. 4.1.5 GSV - GPS SATELLITE IN VIEW Number of satellites in view, PRN number, elevation angle, azimuth angle, and C/No. Only up to four satellite details are transmitted per message. Additional satellite in view information is sent in subsequent GSV messages.

Format: $GPGSV,. Field Example Description Total number of GSV messages to be transmitted Number of current GSV message Total number of satellites in view, 00 12 Satellite PRN number, GPS: 01 32, SBAS: 33 64 (33 = PRN120) Satellite elevation number, 00 90 degrees Satellite azimuth angle, 000 359 degrees C/No, 00 99 dBNull when not tracking Checksum.

4.1.6 RMC - RECOMMANDED MINIMUM SPECIFIC GPS/TRANSIT DATA Time, date, position, course and speed data. Format: $GPRMC,. Example: $GPRMC,104549.04,A,2447.2038,N,E, 016.0,221.0,250304,003.3,W,A.22. Field Example Description 104549.04 UTC time in hhmmss.ss format, 000000.00 235959.99 Status, 'V' = navigation receiver warning, 'A' = valid position 2447.2038 Latitude in dddmm.mmmm format Leading zeros transmitted Latitude hemisphere indicator, 'N' = North, 'S' = South Longitude in dddmm.mmmm format Leading zeros transmitted Longitude hemisphere indicator. 4.1.7 VTG - COURSE OVER GROUND AND GROUND SPEED Velocity is given as course over ground (COG) and speed over ground (SOG). Format: GPVTG,T,M,N,K,. Example: $GPVTG,221.0,T,224.3,M,016.0,N,0029.6,K,A.1F Field Example Description 221.0 True course over ground, 000.0 359.9 degrees 224.3 Magnetic course over ground, 000.0 359.9 degrees 016.0 Speed over ground.

APPENDIX B DEFAULT VALUES The product has the following factory preset default values: Datum: 000 (WGS-84) NMEA Enable Switch: ( 1 sec. Output) ( 5 sec.

Output) ( 5 sec. Output) ( 1 sec.

Output) ( 1 sec. Output) Checksum ON Baud Rate: 4800 Baud Elevation Mask. TROUBLESHOOTING Problem Reasons Solutions No Position Weak or no GPS signal Place the HI-204 -USB under output but can be received at the an open space, then, press timer is place of HI-204 -USB 'Reset' counting unit At outdoor space but To try again, go to outdoor and GPS signal is blocked press 'Reset' or connect. USB Driver Setup Guide HI-204 -USB USB GPS Receiver.

Introduction of GPS USB Driver Files The USB GPS driver group consists of 6 files. Files Name Description of Specific Property DRemover982K.exe Type: Application This execution file removes GPS USB driver from the PC. Serwpl.inf Type: Setup Information This file provides major setup information. Figure 1: Screen of GPS USB Driver Group Figure 2: Screen of GPS USB Driver Win 2000 and Win XP System File.

Figure 3: Screen of GPS USB Driver Win 98 and Win ME Group. B.Windows 98 Interface 1. Install GPS USB Driver Before the installation of GPS USB driver, there are three procedures required. The first thing is to turn on PC in the Windows environment. The second thing is to copy USB driver into HDD. The third thing is to plug the GPS receiver into the USB port of PC and then follow the installation guide.

Step 1: Click the 'Next' button Figure 4: Win 98 Automatic Installation Driver Screen. Step 2: Select 'Automatically'and click the 'Next' button Figure 5: Win 98 Automatic Installation Driver Screen. Step 3: Specific driver location and click the 'Next'button Figure 6: Win 98 Automatic Installation Driver Screen. Step 4: Click the 'Next'button Figure 7: Win 98 Automatic Installation Driver Screen. Step 5: Click the 'Finish'button Figure 8: Win 98 Automatic Installation Driver Screen.

Check Enable COM Port Number After you install GPS USB driver, you should know which COM port is available, and check enabled COM port number. You need to know the COM port assignment for the GPS receiver, when configuring map or chart software. Please notice that this remark is very important.

Step 2: Double-click the 'Control Panel' icon Figure 10: My Computer Screen. Step 3: Double-click the 'System' icon Figure 11: Control Panel Screen.

Step 4: Press'Device Manager' button Figure 12: System Properties Screen. Step 5: Slect 'USB to Serial Port' (COM3) and click 'Propertes' button Figure 13: System Properties Screen. Step 6: Browse COM3 properties Figure 14: System Properties Screen. Remove GPS USB Driver If you want to update the USB driver, you should remove existing driver and install new one.

Step 1: Remove GPS USB driver by double-clicking the icon show in Figure-15. A dialog window shown in Figure-16 will be pop up. Windows XP Interface 1. Install GPS USB Driver Before the installation of GPS USB driver, there are three procedures required.

The first thing is to turn on PC in the Windows environment. The second thing is to copy USB driver into HDD. The third thing is to plug the GPS receiver into the USB port of PC and then follow the installation guide.

Usb Gps Driver

Step 2: Select 'Include this location in the search' OR 'Browse' to specific GPS USB driver location Figure 19: Win XP Automatic Installation Driver Screen Step 3: Click 'Continue Anyway' button Figure 20: Win XP Automatic Installation Driver Screen. Step 4: Finish screen Figure 21: Win XP Automatic Installation Driver Screen Step 3: Click 'Continue Anyway' button Figure 22: Win XP Automatic Installation Driver Screen. Check Enable COM Port Number After you install GPS USB driver, you should know which COM port is available, and check enabled COM port number. You need to know the COM port assignment for the GPS receiver, when configuring map or chart software. Please notice that this remark is very important. Step 2: Select 'Hardware' Figure 23: System Properties Screen.

Step 3: Select 'Device Manager' Figure 24: System Properties Screen. Step 4: Select Ports (COM&LPT) Figure 25: Device Manager Screen.

Step 5: Select COM4 Figure 26: Device Manager Screen. Step 6: Select 'Driver' Figure 27: USB-to-Serial Bridge Screen. Step 7: Browse COM4 properties Figure 28: USB-to-Serial Bridge Properties Screen. 3 Remove GPS USB Driver If you want to update the USB driver, you should remove existing driver and install new one. Step 1: Remove GPS USB driver by double-clicking the icon show in Figure-29.

A dialog window shown in Figure-30 will be pop up. Change COM Port Number Application Program If the notebook assigns COM number to COM5, then can to execute SetCOM.exe for COM number change. Step 1: For change COM port number assign by double-clicking the icon show in Figure-32, and then small icon shown in Figure-34 will be pop up. Figure 32: SetCOM.exe Icon Figure 33: Start bar on the right-below corner of screen Figure 34: Start bar on the right-below corner of screen. Step 2: by clicking the icon show in Figure-34.

A dialog window shown in Figure-35 will be pop up. Figure 35: COM port number change screec. Step 3: for example change COM3 become COM4, first Click COM3 and COM4 then Click 'Set' button Figure 36: COM port number change screec Step 4: Click 'Yes' button Figure 37: Notification Screen. Important Remarks 1. If your system is Windows Millennium, please refer to Windows 98 installation guide.

If your system is Windows 2000, please refer to Windows XP installation guide. If you follow the steps but the GPS receiver doesn't work, please try to unplug the GPS receiver from the USB port, wait for 58 seconds, and re-plug the GPS receiver into your PC. If your GPS receiver is recognized as a Microsoft serial mouse, there are two ways and you can choose either one to solve the problem. The first is to unplug the GPS receiver from PC, wait for 58 seconds, and re-plug the GPS receiver into your PC. W AT E R P R O O F U S B G P S Re c e i ve r.