Convert File Cabinet To Hanging Folders
DIY File Cabinet Hardware If you are looking to get a more organized desk by converting a drawer into file cabinet, offers a few ideas on how to create file frame systems using various unique hardware - for standard letter-size or legal-size file folders. Use these black PVC folders hangers to transform desk drawers into hanging file systems. The 'h' shaped folder hanger can be cut to length and placed on the top edge of both sides of a drawer. Hanger is designed for 1/2' thick drawer sides. Allow at least 1' above drawer to the top of the cabinet opening to provide clearance for folder labels. Metafile converts any drawer into a filing cabinet. Just install Blum's Metafile in a spare drawer to create a functional filing system in minutes.
File Cabinet Hardware. Use these black PVC folders hangers to transform desk drawers into hanging file systems. The 'h' shaped folder hanger can be cut to length.
Filing Cabinet Hanging Folder Frame
Features: ⦿ Installation requires no special machining ⦿ May be used with both Pendaflex letter and legal folders This kit allows you to mount files crosswise to create space and improve access. Converting your file drawer from a standard in-line to a transverse system lets you access files easily. No more digging for the files in back and scraping your knuckles on the file drawer above! And you can hang legal sized files in a standard letter width drawer. Use in any drawer with 1/2' sides.
Contains 2 pieces of 28' file rail, 2 pieces of 11-7/8' roll-formed metal bars and 4 transverse file clips. Unique file drawer system for both legal and letter size file folders. Each Unit Contains: ⦿ Wire frame ⦿ Corner connectors ⦿ T-rod connections ⦿ Mounting screws are NOT included Supports hanging files on wood drawers.
Set includes black metal 13' front and back rails, 22' cut-to-size side rails, cut-to-size brackets, and side-to-side rail. Easy to adjust between filing configurations - rails snap in and out of position without tools. Able to withstand thousands of back and forth cycles. Accommodates letter, legal and A4 sizes. As an associate of the affiliate program, we receive a small commission for sales generated through links to their products.
Thanks for shopping!
Shares 35 I’m still making slow progress on my new. I finally finished building the two cabinets with hanging file folder drawers that will hold up the two ends of the future countertop. The drawers are 24″ deep with full extension glides so one could store a LOT of folders if they needed. How to build a hanging file folder drawer You can build a new drawer or use an existing drawer if it’s the right size. If building a new drawer, you can follow my but adjust the size to accommodate the files. I built my drawer 14″ wide by 10″ deep. When planning your cabinet, make sure to leave 1″ clearance above the top of the file drawer so the hanging file tabs will clear the faceframe or drawer above the files.
I purchased the metal bars at Home Depot. They’re about 1/8″ thick and 3/4″ tall and came in 3′ lengths. I marked the top of the drawer box where the center of the bar needed to sit. The bars will sit 12 1/4″ apart. I set up my table saw so the blade would cut about 1/2″ deep (I wanted the bar to sit a bit higher than my drawer) and adjusted the fence so the blade lined up with my mark. Then I ran my drawer box all the way through so it cut a slit in the front and back parts of the drawer.
Convert File Cabinet To Hanging
Flipped it around and cut slits in the other side. Obviously the drawer box is sitting on the table upside down –so the slits are being cut into the top of the drawer. Check to make sure your bar fits in your cut. Cut the bar to length with a hacksaw and then rub it on sandpaper to smooth it out so there aren’t any sharp edges. You may have to glue or nail a block on the back of the drawer to keep the bar from sliding back.
The drawer front will hold it in place in the front. My bars are tight (I used a rubber mallet to ease them in so I don’t think there will be any movement but if your bar is slightly thinner or cut is wider you may need a block). Just for fun, I wanted to paint my bars with a bright color. I cut slits in some scrap wood to hold the bars upright while I sprayed them. Wes thought the bright yellow bars were odd but I like ’em.
He can sand the paint off of his if he wants to bring them back to plain ole’ metal. 😉 If you liked this post, you might find other helpful posts in my gallery.