Airlive Wireless Ap Manual
. WH-5400CPE High Power Outdoor Solution User’s manual. T he Wireless Technology Standard The Wireless Access Point utilizes the 802.11b and the 802.11g standards.
View and Download AIRLIVE WH-5400CPE user manual online. AIRLIVE Wireless Access Points. WH-5400CPE Wireless Access Point pdf manual download. View and Download AIRLIVE WH-5400CPE user manual online. AIRLIVE Wireless Access Points. WH-5400CPE Wireless Access Point pdf manual download.
The IEEE 802.11g standard is an extension of the 802.11b standard. It increases the data rate up to 54 Mbps (108Mbps in Super G mode) within the 2.4GHz band, utilizing OFDM technology.
Roaming Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID.
Before enabling you consider roaming, choose a feasible radio channel and optimum access point position. ceiling (instead of at an angle) for better reception. Building materials can impede the wireless signal - a solid metal door or aluminum studs may have a negative effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials. Network Topology – AP Mode and Client Mode Wireless Client Wireless AP Mode Mode Network Topology – Gaming Bridge Mode Peer to Peer Gaming Ad hoc Ad hoc.
Network Topology – Repeater Mode Wireless Repeater Mode Network Topology – WDS Point to Point Mode Wireless Client Mode. Network Topology – WDS Point to Multi-Point Mode WDS P2MP Mode. CPE Installation Diagram.
Hardware Installation Making a Connection Attention: The cable distance between the Router and PC/hub/Switch should not exceed 100 meters. Make sure the wiring is correct.
In 10Mbps operation, Category 3/4/5 cable can be used for connection. To reliably operate your network at 100Mbps, you must use Category 5 cable, or better Data Grade. AP Configuration Using Locator While entering the Locator utility, the Locator will automatically search the AP available on the same network.
Locator will show the Device Name, Device Type, IP Address, Ethernet MAC Address and Firmware Version in first page. Before start using Locator, make sure you disable personal firewall installed in you PC. After type in correct user name and password, the utility will lead you into “IP Setting” page. Here you can choose to get IP from a DHCP server or specify IP address manually. Choose to obtain an IP address from DHCP server if your environment or ISP provide DHCP server. You may assign any name to the Access Point.
Memorable, Unique names are helpful especially if you are employing multiple access points on the same network. The device name needs to be less than 32 characters. After verify the name you input and click “Next” to continue the setting. Choose repeater mode if you want to extend the range of your original AP. Note: due to the built-in internal directional patch antenna, repeater mode and WDS option do not apply in WH-5400CPE. Here we choose the AP to work in Access Point mode, and then the utility will ask for SSID, Channel and Wireless Mode. Keep the default value if you do not have special requirement for these settings.
SSID: airlive Channel: Smart Select Wireless Mode: 2.4GHz 54Mbps (802.11g). Next page is wireless security setting; you can choose different level of security support for your wireless environment here. The default value is “Disable” which means anybody who can receive the wireless signal can link to your access point. Once you choose different security level, your wireless LAN card will also need to have corresponding security setting as well. After finish the security setting, you can click on the “Finish” button to jump to confirmation page.
In the confirmation page, the Locator utility will show you the new settings and old settings in a comparison chart. If you agree with all the changes in the table, just easily click on the “OK”. Congratulations!! Now you have finished all setting needed to the access point by just a few mouse clicks. AP Configuration Using Web User Interface Before Setup.
Verify the IP address setting You need to configure your PC’s network settings to obtain an IP address. Computer use IP addresses to communicate with each other across a network, such as the Internet. From the taskbar, click the Start button, select Settings. Wireless Configuration - AP Mode System Status – The first page appears in main page will show “System Status - System Summary” automatically, you can find detail system configuration in this page including System Information – This will display system name and both Ethernet MAC address and Wireless MAC address. multiple access points on the same network.
The device name needs to be less than 32 characters. After verify the name you input and click “Apply” to save the setting.
Country/Region – Here you can set the AP to follow different country and region regulation. IP Settings – IP Setting page can configure system IP address. Default IP address is 192.168.1.20 and Subnet Mask is 255.255.255.0. You can manually input IP address setting or get an IP from a DHCP server.
If use DCHP to get IP address, use Locator utility to find the access point later. Wireless Network - At Wireless Network page can set “SSID” / “Wireless Mode” and “Channel”. AP supports not only standard 11b/g but also 108M SuperG. (Note: 108 M ® SuperG only works with Atheros based 11a/g solution) Wireless Network Name (SSID) - The SSID is the unique name shared among all points in a wireless network. provided to correspond with your network settings.
All points in your wireless network must use the same channel in order to function correctly. The default setting is “SmartSelect” means the system will pick best channel for you automatically. Stay with default setting if you do not have special request on channel selection. WEP is a basic encryption method, which is not as secure as WPA. To use WEP, you will need to select a default transmit key and a level of WEP encryption, Authentication type – Select “Open System” to communicate the key across the network. WPA-PSK stands for Wi-Fi Protected Access – Pre-Shared Key.
WPA-PSK is design for home users who do not have RADIUS server in their network environment. WPA can provide better security level than WEP without difficult setting procedure.
PassPhrase - Enter a WPA Shared Key of 8-63 characters. The Shared Key should be also applying the clients work in the same wireless network. WPA option features WPA used in coordination with a RADIUS server.
(This should only be used when a RADIUS server is connected to the Access Point.) RADIUS Server – Here enter the IP address of your RADIUS server. RADIUS Port – Port number for RADIUS service, default value is 1812 RADIUS Secret –. Wireless Advance Settings - The page below can help users to configure advanced wireless setting. Before making any changes at this page, please check your wireless settings on other system as well, as these changes will alter the effectiveness of the Access Point. In most cases, these settings do not need to be changed. enter sleep mode, thus saving power, but interferes with wireless transmissions.
Fragment Length (256-2346) – This specifies the maximum size a data packet will be before splitting and creating a new packet and should remain at its default setting of 2,346. A smaller setting means smaller packets, which will create more packets for each transmission. Wireless Station List - Wireless Station List page can help user identify current clients who already associated to the AP. You can also click on the MAC address column then the system will show the detail technical information for each wireless station. The page below describes the detail connection information with each station.
Backup/Restore Setting / Firmware Upgrade and Reboot - In Management section, you can Backup/Restore Setting, Firmware Upgrade and Reboot the system in following pages. Backup the current settings to a file – Click on the “Backup” button, system will prompt you where to save the backup file. You can choose the directory to save your configuration file. Firmware Upgrade – Enter the location of the firmware upgrade file in the file path field, or click the “Browse” button to find the firmware upgrade file. Then click on the “Upgrade” button, and follow the on-screen instructions. The whole firmware upgrade process will take around 60 seconds.
Wireless Ap Router
Wireless Configuration – WDS Mode (P2P & P2MP) Due to built-in internal directional patch antenna, WDS does not apply in WH-5400CPE. This operation option is reserved for future application. WDS (Wireless Distribution System) operation as defined by the IEEE802.11 standard has been made available. In IEEE 802.11 terminology a 'Distribution System'.
Considerations before installation – Loop Prevention – Be careful to plan you WDS connections, prevent your wireless network topology to have loop. Once loop shows up, you network traffic will become unstable. Performance – The system can support up to 8 WDS links.
But all links and wireless stations that operate at the same time will all share single radio bandwidth. Wireless Configuration – Wireless Client Mode AP can also work as an Ethernet client bridge to connect up to 16 Ethernet device into wireless network. In order to setup the AP to work in Ethernet bridge mode, you need to choose “Wireless Client” mode and click “Apply” at System Properties page. Connection Status - Connection – This column show current connection status. If AP already connect to an Access Point or station, here will show the MAC address of the associated Access Point or station.
Otherwise, connection column will show “N/A” which means no connection to any Access Point or station. Network Type –. Wireless Network - Network Mode – You can set the wireless client into 2 different modes by clicking radio button.
Wireless Client (Infrastructure) act as an AP client while Ad-hoc can support peer to peer network. Both Infrastructure and Ad-hoc can support up to 108M SuperG transmission. Wireless Mode - Default setting is “2.4GHz 54Mbps (802.11g)”. in your current environment. The Site Survey page can help you identify all the APs currently working in your environment. Just easily click on the BSSID column, the system will join you to the SSID you specify.
In the Site Survey page you can also see the details of all SSID currently available. after reboot. Wireless Security – WEP is a basic encryption method, which is not as secure as WPA. To use WEP as a client, you will need to input a transmit key and a level of WEP encryption exactly the same as the Access Point. Shared keys input type –.
Shared Key should be also applying the Access Point work in the same wireless network. Cipher Type - WPA gives you two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES. Remember to click on “Apply” to make sure all changes are made before leaving this page.
Wireless Configuration – Wireless Repeater Mode Due to built-in internal directional patch antenna, repeater mode does not apply in WH-5400CPE. This operation mode is reserved for future application. When set the Access Point to Repeater mode, the AP is able to talk with one remote access point within its range and retransmit its signal. After click on the “Site Survey” button, you can choose the Access Point you need to extend its range by clicking on “BSSID” column. Then “Apply” the change to make sure system working properly with new setting. After all the changes are made, you can check the “Connect Status” page to check current SSID and link quality / signal strength. Appendix A: Glossary 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and anoperating frequency of 2.4GHz.
802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Gateway - A device that interconnects networks with different, incompatible communications protocols. Hardware - The physical aspect of computers, telecommunications, and other information technology devices. IEEE (The Institute of Electrical and Electronics Engineers) - An independent institute that develops networking standards. Infrastructure - A wireless network that is bridged to a wired network via an access point. Subnet Mask - An address code that determines the size of the network. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports.
Best Wireless Ap
A device for making, breaking, or changing the connections in an electrical circuit. Appendix B: Specification Standard support IEEE802.11b IEEE802.11g IEEE802.3 IEEE802.3u Interface Wireless IEEE802.11b/g One 10/100 RJ-45 port SDRAM 8Mbyte Flash 2Mbyte Max. Bandwidth Ethernet Full Duplex: 200Mbps (for 100BASETX), 20Mbps (for 10BaseT) Half Duplex: 100Mbps (for 100BaseTX), 10Mbps (for 10BaseT) Wireless 1, 2, 5.5, 6, 9, 11, 12, 24, 36, 48, 54, 108Mbps Auto Fall-Back Wireless Radio. − Transmit power (Full, Half, Quarter, Eighth, Minimum) − Beacon Interval (20-1000): 100 − Data Beacon Rate (DTIM (1-16384): 1 − Fragment Length (256-2346): 2346 − RTS Threshold (256-2346): 2346 − Short Preamble: Enable − Allow 2.4GHz 54Mbps Station Only −.
This is crazy. I've connected the Airlive WL5460AP with an ethernet cable to the computer. The computer detects the access point, but doesn't establish connection. The LAN port is LAN1 according to the manual. The Service Line told me to configure my PC with a specific IP address 192.168.100.xxx where xxx shouldn't be 252 (reserved to the AP).
I changed the /etc/network/interfaces file according to. But still, Ubuntu 11.10 doesn't connect. The Service Line told me to try with Windows under VMWare, but after trying, I think that VMWare makes use of the underlying Linux kernel. So, any idea how to establish connection to this Linux unfriendly hardware? Oh, the idea I have is to have a universal repeater of the existing ISP router signal. I also tried to wire the AP directly to the router, but without success (maybe I should have used a special LAN port).